How To Find the Fault Code on a Daikin Mini Split System

By | May 16, 2023

How To Find the Fault Code on a Daikin Mini Split System
If you have a Daikin mini split that is not working, the fault codes can be pulled using the remote control.
How To Find the Fault Code on a Daikin Mini Split System Green Light
A flashing green light often appears on a Daikin unit when there is a problem.

The remote control Cancel button is used to pull the code from the unit.

Once the code is known, the problem can be troubleshot and fixed.

The Cancel button on the remote control is held for 5-6 seconds until a 00 is shown on the display.

Once in the mode, the Cancel button will cycle through the codes giving short beeps for non-errors and a long beep for the problem error.

This has been tested and works with L-Series, Q-Series, Cobra models, and more.

Below are the steps to follow to find the error code on a Daikin mini split.

How To Find the Fault Code on a Daikin Mini Split System

  1. On the remote control, find the Cancel button.
  2. How To Find the Fault Code on a Daikin Mini Split System Step 1

  3. Press and hold the Cancel button for 6 seconds.
  4. How To Find the Fault Code on a Daikin Mini Split System Step 2

  5. 00 will flash on the remote display.
  6. How To Find the Fault Code on a Daikin Mini Split System Step 3

  7. Press the Cancel button again once to cycle through the fault codes.
  8. How To Find the Fault Code on a Daikin Mini Split System Step 4

  9. A short beep will be heard each time the Cancel button is pressed. A Long beep will be the error code.
  10. How To Find the Fault Code on a Daikin Mini Split System Step 5

Daikin Mini Split Fault Code Meaning

Once the code is found, it can be looked up using the Daikin error code chart.
How To Find the Fault Code on a Daikin Mini Split System Error Code
For example, the error code U4 was found above, with the chart showing there is a communication problem between the indoor and outdoor units.

A U4 error code can often be cleared by turning off the power to both indoor and outdoor units at the breaker.

Read here for a full list of Daikin Mini Split Error Codes.

Daikin Mini Split Error Codes and Meanings

Error CodeStatus
00NORMAL
U0REFRIGERANT SHORTAGE
U2OVER-VOLTAGE DETECTION
U4SIGNAL TRANSMISSION ERROR (BETWEEN INDOOR AND OUTDOOR UNIT)
A1INDOOR UNIT PCB ABNORMALITY
A5FREEZE-UP PROTECTION OR HEATING PEAK-CUT CONTROL
A6FAN MOTOR (DC MOTOR) ABNORMALITY
C4INDOOR HEAT EXCHANGER THERMISTOR ABNORMALITY
C7FRONT PANEL OPEN /CLOSE FAULT
C9ROOM TEMPERATURE THERMISTOR ABNORMALITY
EAFOUR WAY VALVE ABNORMALITY
E1OUTDOOR UNIT PCB ABNORMALITY
E5OL ACTIVATION (COMPRESSOR OVERLOAD)
E6COMPRESSOR LOCK
E7DC FAN LOCK
F3DISCHARGE PIPE TEMPERATURE CONTROL
H0COMPRESSOR SYSTEM SENSOR ABNORMALITY
H6POSITION SENSOR ABNORMALITY
H8DC VOLTAGE / CURRENT SENSOR ABNORMALITY
H9OUTDOOR TEMPERATURE THERMISTOR ABNORMALITY
J3DISCHARGE PIPE THERMISTOR ABNORMALITY
J6OUTDOOR HEAT EXCHANGER THERMISTOR ABNORMALITY
L4RADIATION FIN TEMPERATURE RISE
L5OUTPUT OVERCURRENT DETECTION
P4RADIATION FIN THERMISTOR ABNORMALITY

Summary
If you have a Daikin mini split that is not working properly, finding the error code is the first step to fixing it.

The code can be found on many Daikin models using the remote control and Cancel button.

Once the code is found, it can be looked up using the error code chart, which will show the problem.

Be sure to write down the code in case a technician is called to look at the unit.

2 thoughts on “How To Find the Fault Code on a Daikin Mini Split System

  1. Anburaj

    Daikin split unit running after Orange light blinking unity shutdown

    Reply
  2. Richard Dodson

    After a few days of the thermostats being set at 50 and mostly in activity, the green light blinks and the system will not work. Cycling the power at the CB panel solves the problem and the system works fine

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.