How To Use a Refrigerant Recovery Machine on an HVAC System

By | September 8, 2022

Freon Refrigerant Recovery
Refrigerant recovery from an HVAC system has been mandatory since 1995 when the EPA enacted the Montreal Protocol and required 608 certification of all technicians. Refrigerant must be recovered; otherwise, huge fines can be imposed.

The EPA allows for de-minimis release, or basically refrigerant released when connecting hoses to and from a unit or tank.

Items Needed for Refrigerant Recovery

How To Use a Refrigerant Recovery Machine New

  • Recovery tank (Tanks with a yellow top are designated Recovery Tanks.)
  • Recovery Machine.
  • Refrigerant Scale.

The basic items needed are HVAC gauges to connect hoses between an HVAC system, recovery machine, and recovery tank.

How To Use a Refrigerant Recovery Machine

  1. The gauges should be turned off and connected to the high and low sides of the unit to be recovered from. Red goes to the high side; Blue goes to the low side.
  2. freon recovery
     

  3. The yellow center hose goes to the suction line of the recovery machine-marked IN; a dryer should be placed here to help keep contaminants out.
  4. hvac dryer
     

  5. A single-hose goes OUT of the recovery machine to the recovery tank.
  6. Refrigerant Recovery
     

  7. Set the recovery tank on a scale to measure how much refrigerant is removed from the unit and avoid overfilling the recovery tank. By law, a tank can only be filled to 80 percent capacity.
  8. recover tank on scale
     

  9. After everything is connected, the air is purged from the hoses. This is done by opening all the valves from the unit to the tank; only the tank valve should be off, then at the tank letting the air push out of the hoses. This will only be done for a few seconds. At the tank, unscrew the hose slightly until the air is heard escaping; after a second or two, re-tighten the connection to the tank. The refrigerant will be under pressure and push the air out of the lines.
  10.  
    Pressure at the recovery machine will show when all valves are open.
    pressure at recovery machine
    Purging the lines
    purge hvac system
     

  11. After the lines are purged, the recovery machine is ready to be turned on. The recovery tank valve, along with all other valves, should be open; the recovery machine can be turned on.
    recover machine in action
  12.  

  13. At the HVAC gauges and recovery machine, you should see the pressure begin to drop as the refrigerant goes into the recovery tank. Be sure to watch the scale as not to overfill the recovery tank; a tank should never be filled past 80 percent of its capacity. The recovery machine should be working up to it reaches 0 psi on the low-side of the recovery machine. Don’t go below 0 psi, as if there is a leak, you will be sucking air. Most new recovery machines will turn themselves off automatically when they reach 0 psi.
    recovery machine gauges
  14.  

  15. After the recovery machine has reached zero psi, the recovery machine needs to be purged. To do this, turn the low-side blue valve to purge and the high red side to purge on the recovery machine. Then watch the gauges on the recovery machine. The low side will go from high to low, and the recovery machine should shut down when it is done.
  16. recover machine guages
     

  17. Close all the valves, especially the recovery tank, and you are done.

Summary
Using a recovery machine on an HVAC unit is necessary when a refrigerant is still in a system.

For example, if a compressor needs to be replaced, the refrigerant would need to be recovered first before replacing the component.

There is more that can be done to speed up the process of recovery, such as turning on the blower motor so the liquid doesn’t freeze getting quicker recovery times.

Refrigerants should never be mixed R-22, R134, R-410 should all be kept separate. Old refrigerant shouldn’t be mixed if the refrigerant is going back into the system it was removed from.



Category: HVAC how to Portable Refrigerant Recovery Machine

About Aaron H. Benetti

Aaron H. Benetti has worked in the HVAC field since 1991. He began his career as an HVAC installer and later began doing troubleshooting and repairs. Around 2010, he began to write books on HVAC topics, mainly tutorials and how-to information. Currently, Aaron writes many articles and posts for websites as well as books and videos on HVAC topics.

9 thoughts on “How To Use a Refrigerant Recovery Machine on an HVAC System

  1. Astir

    I from my experience is a mandatory to vaccum the gas cylinder before recovery starts.

    Reply
  2. ALUNGILE

    Thank you for the video it was very helpful

    Regards

    A.S Stofile

    Reply
  3. Richard

    I found a recovery tank the other day mark mix gases. R401A, R410A, R409A I wanted to be sure this is a tank that is able to be mix or not.

    Reply
  4. M.Basheer

    While doing recovery from empty 40kg cylinder to another 12kg cylinder head pressure increase after 2kg refrigerant recovered and the machine stops. Before I used to recovery 8kg refrigerant from different empty cylinders to the recovery cylinder 12kg.

    Reply
  5. Karem

    Thanks so much for the explanation about the recovery process

    Reply
  6. Don polido

    Is recovered refregerant can be use again for charging an AC system..?

    Reply
    1. John Esparza

      You charge it like you would out of the refrigerant tank. The recovery tank becomes your supply tank in other words.

      Reply
  7. tommy sts

    is there a way to test a recovery machine with out hooking it up to a system?

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.