How To Use A Refrigerant Recovery Machine

By | November 9, 2014

Freon Refrigerant Recovery

Refrigerant recovery from a HVAC system has been mandatory since 1995 when the EPA enacted the Montreal Protocol and required 608 certification of all technicians. refrigerant must be recovered otherwise huge fines can be imposed.
 
The EPA does allow for de-minimis release, or basically refrigerant released when connecting hoses to and from a unit or tank.
 
What Will Be Needed
HVAC gauges to connect hoses between a HVAC system, recovery machine, and recovery tank.
Recovery tank, tanks with a yellow top are designated Recovery Tanks.
Recovery Machine
Refrigerant scale
 
1…The gauges should be turned off and then connected to the high and low sides of the unit to be recovered from. Red goes to the high side, Blue goes to the low side.
freon recovery
 
2…The center yellow hose goes to the suction line of the recover machine marked IN, a dryer should be placed here to help keep contaminants out.
hvac dryer
 
3…A single hose than goes OUT of the recovery machine to the recovery tank.
Refrigerant Recovery
 
4…Set the recover tank on a scale to measure how much refrigerant is removed from the unit, and ovoid overfilling the recovery tank. By law a tank can only be filled to 80 percent capacity.
recover tank on scale
 
5…After everything is connected we need to purge the air from the hoses. This is done by opening all the valves from the unit to the tank, only the tank valve should be off, than at the tank letting the air push out of the hoses. This will only be done for a few seconds. At the tank unscrew the hose slightly until air is heard escaping, after a second or two re-tighten the connection to the tank. The refrigerant will be under pressure and push the air out of the lines.
 
Pressure at the recovery machine will show when all valves are open
pressure at recovery machine
Purging the lines
purge hvac system
 
6…After the the lines are purged we are ready to turn on the recovery machine. The recovery tank valve along with all other valves should be open, than the recovery machine can be turned on.
recover machine in action
 
7…At the HVAC gauges and recovery machine you should see the pressure begin to drop as the refrigerant goes into he recovery tank. Be sure to watch the scale as to not overfill the recovery tank, a tank should never be filled pass 80 percent of its capacity. The recovery machine should be working up to it reaches 0 psi on the low side of the recovery machine. Don’t go below 0 psi as if there is a leak you will be sucking air. Most new recovery machines will turn themselves off automatically when they reach 0 psi.
recovery machine gauges
 
8…After the recovery machine has reached zero psi and shut off the recover machine needs to be purged. To do this turn the low side blue valve to purge and the high red side to purge on the revery machine. Then watch the gauges on the recovery machine. The low side will go from high to low and the recovery machine should shut down when its done.

recover machine gauges

recover machine gauges


recover machine guages
 
9…Close all the valves, especially the recovery tank, and you are done.
 
Summary
There is more that can be done to speed up the precess of recovery such as turning on the blower motor so the liquid doesn’t freeze, getting quicker recovery times.
 
Refrigerants should never be mixed R-22,R134, R-410 should all be kept separate. Old refrigerant shouldn’t be mixed if the refrigerant is going back into the system it was removed from.
 

 


 




 

9 thoughts on “How To Use A Refrigerant Recovery Machine

  1. M.Basheer

    While doing recovery from empty 40kg cylinder to another 12kg cylinder head pressure increase after 2kg refrigerant recovered and the machine stops. Before I used to recovery 8kg refrigerant from different empty cylinders to the recovery cylinder 12kg.

    Reply
  2. tommy sts

    is there a way to test a recovery machine with out hooking it up to a system?

    Reply
  3. Richard

    I found a recovery tank the other day mark mix gases. R401A, R410A, R409A I wanted to be sure this is a tank that is able to be mix or not.

    Reply
  4. AMARJIT MAJHI

    I AM SATISFIED, HOW TO USE OF THE RECOVERY MACHINE IN WORKING PLACE ,IT WAS VERY EFFECTIVE

    Reply
    1. John Esparza

      You charge it like you would out of the refrigerant tank. The recovery tank becomes your supply tank in other words.

      Reply
  5. ALUNGILE

    Thank you for the video it was very helpful

    Regards

    A.S Stofile

    Reply

Leave a Reply to AMARJIT MAJHI Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.